How to Replace a Sawgrass SG1000 Waste Collection Unit
Replace the Sawgrass SG500 or SG1000 waste collection unit by powering down the printer, removing the full unit, installing the replacement, and following the printer's reset or maintenance prompt. Keep the printer level and handle the waste ink unit carefully to prevent spills.
On this page (9 sections)
- What does the Sawgrass waste collection unit do?
- What should you prepare before replacing it?
- How do you replace a Sawgrass SG500 or SG1000 waste unit?
- How can you avoid ink spills during replacement?
- Which supplies help with the full sublimation workflow?
- What should you check after installing the unit?
- When should you contact support?
- What is the correct replacement decision?
- Choose A-SUB paper for sublimation transfers, Fancierstudio for pressing a 15 x 15 in transfer area, and Avery paper for dark-fabric inkjet iron-ons. If you are comparing complete SG500 setups, see the best Sawgrass SG500 bundle options.
Replace the Sawgrass SG500 or SG1000 waste collection unit when the printer reports that it is full or requires service. Power down the printer, protect the work area, remove the old unit without tipping it, install the replacement, and complete the printer's maintenance prompt.
The waste collection system holds ink removed during cleaning and flushing. That ink helps keep print quality consistent, and the unit sits apart from the ink cartridges and printhead.
A full waste unit is not low ink, so replacing a cartridge will not clear the warning. Paper, transfer sheets, and a heat press belong to later stages of the workflow.
Use the printer message as the trigger and do not wait for leaks or poor prints. The printer warns early, while the unit can still be removed cleanly.
Menu wording can vary by firmware, so check the official Sawgrass support resources for model-specific instructions before starting. Keep the instructions open while you work.
Have the correct replacement unit and a sealable bag or container within reach before you open anything. Lay down absorbent material and keep the printer level on a stable surface.
Turn the printer off using its normal power control and let any active cycle stop on its own. Do not pull cords or force a panel, and keep the used unit upright from the moment it comes out.
What does the Sawgrass waste collection unit do?
The waste collection unit holds ink removed during printer cleaning and maintenance. It is separate from the ink cartridges and should be replaced when the SG500 or SG1000 identifies it as full.
Do not confuse this service part with sublimation paper or transfer equipment. A full waste unit is a printer maintenance issue, while paper and a heat press are used after an image has been printed.
Before you begin, confirm that the warning names the waste collection unit. If the printer shows a different cartridge, printhead, or general error message, use the matching troubleshooting instructions instead.
What should you prepare before replacing it?
Prepare a level work surface, disposable gloves, absorbent material, and a sealable bag or container. The goal is to keep residual ink away from the printer, desk, floor, and your hands.
Have the replacement unit ready before removing the old one. Keep the printer near its normal position, and avoid moving or tilting it more than the instructions require.
If you are still setting up an SG500 workflow, our guide to how to use a Sawgrass SG500 printer covers the wider print process. For equipment planning, see the sublimation printer machine buying guide.
How do you replace a Sawgrass SG500 or SG1000 waste unit?
Turn the printer off, remove the full unit carefully, fit the replacement in the same position, and follow the on-screen service steps. Use the printer manual or Sawgrass support instructions for the exact access panel and release mechanism on your model.
- Stop the current print or maintenance cycle.
- Turn the printer off using its normal power control.
- Protect the work surface with absorbent material.
- Open the access area identified in the printer instructions.
- Release the full waste collection unit without tipping or squeezing it.
- Place it upright inside a sealable bag or container.
- Install the replacement unit in the correct position.
- Close the access area and turn the printer back on.
- Follow any reset, confirmation, or maintenance prompt.
- Check for warnings before sending another print job.
Do not force a panel, connector, or latch. If the replacement does not seat correctly, stop and check the model instructions rather than applying pressure.
How can you avoid ink spills during replacement?
Keep the old unit upright and move it slowly. Residual ink can remain inside the collection unit even after the printer stops showing a normal print screen.
Wear gloves if you have them, and keep absorbent material under the work area. Do not place the unit on fabric, unfinished wood, or any surface that could stain easily.
Seal the used unit before carrying it away. Do not pour its contents into a sink, open the housing, or rinse it unless Sawgrass specifically instructs you to do so.
Does the replacement affect sublimation printing?
The waste unit supports printer maintenance, not the transfer stage. After the printer clears the service warning, confirm that it is ready before sending a design to paper.
For ink choices, read how to choose ink for the Sawgrass SG500 and SG1000. For the paper stage, compare the best sublimation paper for the Sawgrass SG500.
Which supplies help with the full sublimation workflow?
The following products support different parts of a transfer workflow. They do not replace the Sawgrass waste collection unit.
Avery Heat Transfer Paper is 8.5 x 11 in printable transfer paper for dark fabrics, with 5 sheets for inkjet printers. It is designed for dark-colored cotton and cotton/poly fabrics, and it works with standard irons and heat presses.

8.5 x 11 in Avery transfer paper for dark fabrics when you need printable iron-on sheets for a separate heat-transfer project.
See it on AmazonThis paper suits small custom apparel, décor, and gift projects. It is not a waste-ink service part, so it cannot solve a printer maintenance warning.
The Fancierstudio Digital Heat Press 15 x is a 15 x 15 in heat press with 110 volts and 1800 watts. It has electronic time and heat control, adjustable pressure, a silicon-gel base board, and a Teflon-coated heat platen.

A 15 x 15 in digital heat press for applying transfers after the printer and paper stages are complete.
See it on AmazonIts 15 x 15 in work area suits users who need a larger pressing surface for shirts, bags, or mouse pads. It is separate from the printer, so replacing it will not clear an SG500 or SG1000 waste-unit warning.
A-SUB Sublimation Paper 8.5x11 Inch 110 Sheets is 8.5 x 11 in, 125 g sublimation paper with 110 sheets. It is intended for sublimation ink and white or light-colored polyester materials, plus coated ceramic, tile, phone case, metal plate, tumbler, and mug surfaces.

110 sheets of 8.5 x 11 in sublimation paper for the printing stage after the waste-unit service is complete.
See it on AmazonUse only sublimation ink with this paper. Regular ink does not work with it, and the paper is not a replacement for the printer's waste collection unit.
What should you check after installing the unit?
Confirm that the printer no longer shows the waste-unit warning before printing. If the message remains, turn the printer off and check that the unit and access panel are seated as instructed.
Start by reading every message on the screen, not just the first line. A cleared service notice may sit above a separate note about ink levels or paper, so make sure the waste unit message is gone before you load paper.
If another warning remains, follow the steps for that message instead of guessing. If the same full warning appears again, power the printer down and check the replacement unit position again.
It should sit firmly in the same place as the old unit, so close the panel fully and turn the printer back on. Look for the same warning before you try any other fix.
Look for ink outside the collection area, including the surface under the printer and the edges of the access panel. If you see a leak inside the printer, stop using it, keep it powered down, and follow Sawgrass service guidance.
Run only the maintenance or confirmation step the printer requests, as it may confirm the new unit or reset the service count. Do not run extra cleaning cycles to test the replacement, since cleaning sends more ink into the waste system and fills the new unit faster.
The next check is a normal print, not a test pattern you create on your own. Load the correct paper, watch the first sheet for quality and any new message, and keep the used unit sealed until you can dispose of it as local rules require.
When should you contact support?
Contact Sawgrass support if the unit will not release, the replacement will not fit, the printer reports the same full warning after installation, or ink has leaked inside the printer.
Note the exact message before you ask for help, including whether it names the SG500 or SG1000 waste collection unit. Also note your printer model and any code shown on screen, as that helps support point you to the right steps quickly.
Do not force a stuck unit or a panel that will not close, since pressure can break a latch or damage a connector. If the replacement feels loose or will not sit flat, stop and recheck the model instructions.
A unit that is not seated correctly may not be detected by the printer and may leak during the next maintenance cycle. Ask for help if you cannot identify whether the warning applies to the waste collection unit.
Similar names can make the wrong part easy to order, so confirm the part number for your printer before installing anything. If the packaging or part does not match, keep it unopened and ask support what to do next.
Ink inside the printer is a reason to stop and seek guidance, so do not keep printing to see if the problem goes away. Power the printer down while you wait for advice and keep absorbent material in place to catch any further drops.
Support can also help when the warning returns after a correct installation, as that may point to a missed reset step or a separate fault. Clear notes about what you did will make that conversation easier and protect both the printer and your workflow.
What is the correct replacement decision?
For the Sawgrass SG500 waste collection unit or SG1000 version, use the printer warning as the trigger, then follow the model-specific removal and reset instructions. Keep the old unit upright, contain it before disposal, and confirm the warning has cleared before printing.
Choose A-SUB paper for sublimation transfers, Fancierstudio for pressing a 15 x 15 in transfer area, and Avery paper for dark-fabric inkjet iron-ons. If you are comparing complete SG500 setups, see the best Sawgrass SG500 bundle options.
Frequently asked questions
How often should you replace a Sawgrass waste collection unit?
Replace the waste collection unit when the SG500 or SG1000 reports that it is full or needs service. The timing depends on printer use and cleaning cycles, so follow the printer's warning and Sawgrass maintenance instructions instead of using a fixed calendar schedule.
Can you replace the SG500 and SG1000 waste unit yourself?
Yes, the replacement is a service task many owners can perform if the printer instructions allow it. Turn the printer off, protect the work surface, remove the full unit carefully, fit the replacement, and complete any reset or confirmation steps shown by the printer.
What should you do with a full Sawgrass waste unit?
Keep the full unit upright and place it in a sealed bag or container that can hold residual ink. Follow local disposal rules and Sawgrass guidance, and avoid opening, squeezing, tipping, or rinsing the unit unless the manufacturer specifically directs you to do so.
Can a waste collection unit be reused?
Do not assume a full waste collection unit can be emptied and reused. Use a replacement intended for the printer model and follow Sawgrass instructions, because the printer must be able to collect waste ink safely and recognize the service condition.
About this guide: Our look at Sawgrass SG500 and SG1000 waste collection units draws on maker specs, materials and what owners report. See how we research.



