Best picks

9 Best Laser Modules for the xTool D1 (November 2026)

Updated on · By the Handyloom team

The best xTool D1 laser modules include the xTool S1 1064nm Infrared Laser Module for metal jewelry, the LASER TREE Laser Engraving Module for versatile 5W cutting, and the Quarton Economical Red Dot Laser Module for alignment and pointing.

On this page (9 sections)
  1. The best laser modules for xTool D1 owners, ranked by score
  2. How the xTool D1 laser module options stack up
  3. Is a blue diode or infrared module better for a D1?
  4. What voltage and plug does your D1 need?
  5. How much power do you actually need?
  6. Which materials will your module engrave?
  7. How do you set focus and keep a module clean?
  8. What safety gear goes with a new module?
  9. Verdict: which xTool D1 laser module should you buy?

The best xTool D1 laser module for most owners is a 5W to 10W blue diode with TTL/PWM control, because it fits DIY frames, cuts wood and acrylic, and engraves coated metal without the cost of infrared. Infrared modules top this list for metal, but they are built for the S1 or Falcon A1 Pro, not the D1.

If you own a D1, your upgrade path is different from owning an S1. The D1 uses a standard diode mount and a separate driver board, so power, voltage and plug type matter more than brand.

Check those three points before you match power numbers.

Our score weighs specs, features and buyer feedback against what you're shopping for. We compared output power, spot size, focus, voltage, included parts and material limits from the data for each head.

Start with what accessories do you need for a laser engraver if your D1 is new. That guide covers safety glasses, air assist, enclosures and set up tools you will need with any module.

You can also read what is a laser module for a plain explainer on diode vs infrared.

Our picks at a glance

  1. 1 xTool S1 1064nm Infrared Laser Module
    Best for metal jewelry

    xTool S1 1064nm Infrared Laser Module

    9.7/10 our score

    See it on Amazon
  2. 2 LASER TREE Laser Engraving Module
    Best for versatile 5W cutting

    LASER TREE Laser Engraving Module

    9.5/10 our score

    See it on Amazon
  3. 3 Quarton Economical Red Dot Laser Module
    Best for alignment and pointing

    Quarton Economical Red Dot Laser Module

    9.4/10 our score

    See it on Amazon
  1. 4LASER TREE 10W Laser Engraving Module

    LASER TREE 10W Laser Engraving Module

    Best for 10W cutting value
    Check it
  2. 5Genmitsu CFL55 Compressed Spot 5.5W FAC LaserCheck it
  3. 6LASER TREE Laser Module

    LASER TREE Laser Module

    Best for thick material cutting
    Check it
  4. 7Creality Falcon 2W 1064nm Infrared Laser ModuleCheck it
  5. 8ORTUR LU2-10A Laser Module for Laser MasterCheck it
  6. 9LASER TREE 5W Laser Module

    LASER TREE 5W Laser Module

    Best for 45mm fixed focus
    Check it

The best laser modules for xTool D1 owners, ranked by score

The top three here solve three different jobs. The S1 infrared wins on metal, the LASER TREE 5W wins on balanced cutting, and the Quarton red dot wins only as a pointer, not as an engraver.

Read the fit notes before you buy.

1

xTool S1 1064nm Infrared Laser Module: Best for metal jewelry

xTool S1 1064nm Infrared Laser Module, xTool D1 laser modules
9.7/10Our score
  • 1064nm infrared, 2W output
  • 0.03mm spot, 600mm/s engraving
  • Engraves gold, silver, platinum, copper
  • Cuts aluminum, copper, stainless steel up to 0.05mm

Infrared for metals blue diodes struggle with, made for the S1 rather than the D1.

See it on Amazon

Pros

  • True metal engraving
  • Very fine 0.03mm spot
  • Good on plastic and acrylic

Cons

  • S1 only, not a D1 fit
  • Low cutting power for wood

You should buy this only if you own an S1, not a D1. It is a 2W 1064nm infrared module with a 0.03mm spot and 600mm/s engraving speed.

That wavelength marks gold, silver, platinum, copper and stainless steel that blue diodes mark poorly or cannot mark at all. It also handles zinc, titanium, iron, metal oxides and alloys in the same way.

This reach is why infrared suits bare metal work where a blue head would need paint or marking paper.

In daily use it suits jewelry, tags and small metal parts. It can cut aluminum, copper and stainless steel up to 0.05mm thick.

It also marks leather with less burn and improves plastic and acrylic detail.

The 0.01mm motion precision helps hold fine lines on rings, bracelets and necklaces. A small spot like this rewards clean designs and careful focus.

It suits makers who plan small, detailed pieces on a regular basis.

Set up is simpler when you keep material flat and secured for each job. Watch heat on thin pieces and test on scrap first.

That habit protects detail and keeps edges crisp.

The trade off is clear. It will not cut wood like a 10W blue diode, and it will not fit a D1 frame or driver.

D1 owners who want metal should look at coated metal work with a blue diode, or plan for a different machine.

xTool S1 1064nm Infrared Laser ModuleCheck it on Amazon
2

LASER TREE Laser Engraving Module: Best for versatile 5W cutting

LASER TREE Laser Engraving Module, xTool D1 laser modules
9.5/10Our score
  • 5W output, 450nm, 12V
  • 23mm fixed focus
  • Cuts 4mm plywood in one pass
  • Engraves mirror stainless steel

A balanced 5W blue diode with fixed focus and broad material support.

See it on Amazon

Pros

  • Cuts 4mm plywood one pass
  • Fast stainless engraving
  • Wide DIY compatibility

Cons

  • 12V only, needs adapter for 24V
  • Fixed focus needs care

This suits D1 owners who want one head for wood, acrylic, paper and coated metal. It gives 5W optical power at 450nm with a 23mm fixed focus.

LASER TREE says it cuts 4mm plywood in one pass at 120mm/min. That balance of power and speed makes it a good first upgrade for thin stock.

It suits signs, small parts and gifts where one pass matters.

The 23mm focus makes a small spot, so detail and speed both improve over a long focus head. It engraves mirror stainless steel without black paint.

It cannot engrave blue, purple, white or transparent material, or bare aluminum.

In daily use it also covers MDF, bamboo, leather, plastic and rubber. Those materials are common for D1 owners who mix cutting and engraving.

A quick test on scrap helps you set power before a paid order.

It runs on 12V DC at 1.8A with 5V PWM. A 24V machine needs a driver adapter and an external 12V supply.

That extra step is the main trade off against 24V native heads.

Keep the lens clean and check focus before each thick cut. Regular cleaning helps maintain cutting quality and service life.

Proper eye protection is still required with any Class 4 head.

LASER TREE Laser Engraving ModuleCheck it on Amazon
3

Quarton Economical Red Dot Laser Module: Best for alignment and pointing

Quarton Economical Red Dot Laser Module, xTool D1 laser modules
9.4/10Our score
  • 650nm red dot, under 2.5mW
  • Class 3R, 2.6-6V
  • D7 x L21mm compact
  • APC driver for consistent output

Not an engraver at all, a red dot pointer for alignment and custom mounts.

See it on Amazon

Pros

  • Tiny and cheap to integrate
  • Consistent APC output
  • Good for positioning

Cons

  • Cannot engrave or cut
  • Needs external power and wiring

This is not an engraving module, and that is the point. It is a 650nm red dot under 2.5mW, Class 3R, in a D7 x L21mm body with an APC driver.

It was made for positioning, measuring and pointing. The APC driver holds output steady as voltage changes.

That steady dot makes it useful for repeat alignment tasks in a workshop.

You might mount it on a D1 as a crosshair helper, or use it in a custom jig for alignment. Its small zinc body fits tight spaces better than a full laser head.

It is low cost to integrate into a simple mount.

It needs external power from 2.6 to 6V and has no switch or battery. You must wire it to a suitable supply or battery holder.

It will not engrave, cut or mark metal.

Buy it only as an accessory. If you want cutting power, skip it and choose a 5W or 10W blue diode.

Its value is low cost, small size and steady output for pointing tasks.

In daily use it suits wood, metal and stone processing set ups that need a clear reference point. The beam divergence of 0.6 mRad keeps the dot concentrated.

It works best indoors or in low light where red stays visible.

Quarton Economical Red Dot Laser ModuleCheck it on Amazon
4

LASER TREE 10W Laser Engraving Module: Best for 10W cutting value

LASER TREE 10W Laser Engraving Module, xTool D1 laser modules
9.3/10Our score
  • Real 10W optical, 24V
  • 0.08 x 0.08mm compressed spot
  • Cuts 8mm plywood, 15mm pine one pass
  • Air assist ready

Strong 10W cut power with air assist and a fine compressed spot.

See it on Amazon

Pros

  • Cuts thick wood one pass
  • Fine spot for detail
  • Air assist improves edges

Cons

  • 24V system required
  • Heavier and larger than 5W heads

This suits owners who cut thick wood and acrylic often. It delivers real 10W optical power at 450nm on a 24V input, with a 0.08 x 0.08mm compressed spot.

LASER TREE says it cuts 8mm plywood, 15mm pine and 5mm dark acrylic in one pass. That depth suits sellers who make signs and thicker parts.

It reduces repeat passes and speeds up daily production.

Air assist and a removable eye shield help keep edges clean. The air stream also helps protect the lens from smoke.

For a different xTool model, see xTool M1 air assist installation.

It supports 5V PWM and fits DIY engravers, CNC routers and 3D printer frames with the right mount. For a frame-based build, see laser engraver kits for 3D printers.

The kit includes a driver adapter, spare window glass and focus plates. A spare window is useful because dust or oil on a lens cuts cutting ability.

Check the window before each thick job.

The trade off is size, weight and power draw. At 1.61 lb and 5.7 inches long, it is larger than a 5W head.

It also needs a 24V system, so check your D1 Pro board before you order.

This head suits users who value depth over compact size. Plan for strong ventilation and firm mounting on a lighter gantry.

LASER TREE 10W Laser Engraving ModuleCheck it on Amazon
5

Genmitsu CFL55 Compressed Spot 5.5W FAC Laser: Best for Genmitsu owners

Genmitsu CFL55 Compressed Spot 5.5W FAC Laser, xTool D1 laser modules
9.2/10Our score
  • 5.5W output, 455nm, 12V
  • 0.1 x 0.1mm spot
  • Cuts 4mm plywood one pass
  • Air assist nozzle included

A focused 5.5W Genmitsu head, best if you already own a Genmitsu frame.

See it on Amazon

Pros

  • Small consistent spot
  • Air nozzle protects lens
  • Made for Genmitsu frames

Cons

  • Genmitsu model list only
  • 12V and 3 pin interface

This suits Genmitsu owners more than xTool owners. It gives 5.5W output with a 0.1 x 0.1mm spot at 455nm, on 12V at 2.5A.

Genmitsu says it cuts 4mm plywood in one pass. The small, consistent spot helps with detail as well as cutting.

It suits thin wood, cardboard and acrylic work on a matched frame.

The stock air assist nozzle protects the lens from smoke and helps speed. Fixed focus and upgraded heat dissipation help it run longer.

A UV shield covers the head, but you still need proper eye protection.

In daily use it engraves cardboard, plastic, PCB, aluminium alloy, stainless steel and black metal. It cuts wood, acrylic, cardboard, non woven fabric and bamboo.

That range suits general workshop use on listed machines.

Compatibility is the limit. It is listed for Genmitsu 3020, 3030, 4030, 4040 and 6050 models, plus the Jinsoku LC-60A.

A D1 owner should only consider it if mount holes and the XH2.54 3 pin cable match their board.

Check the plug order for PWM, ground and 12V before first use. Keep the nozzle clear and let the head cool between long runs.

Genmitsu CFL55 Compressed Spot 5.5W FAC LaserCheck it on Amazon
6

LASER TREE Laser Module: Best for thick material cutting

LASER TREE Laser Module, xTool D1 laser modules
9.2/10Our score
  • 30W optical output
  • Cuts 30mm pine, 15mm plywood one pass
  • Built in air assist, dual fan
  • Temperature alarm at 55C

The heavyweight here for thick cutting and color engraving on stainless.

See it on Amazon

Pros

  • Very high cutting power
  • Temperature display and alarm
  • Air assist built in

Cons

  • Large and heavy at 4.53 lb
  • Overkill for thin engraving

This suits production cutting of thick stock. It gives 30W optical output from six 5.5W diodes, with beam compression and built in air assist.

LASER TREE says it cuts 30mm pine, 15mm acrylic and 15mm plywood in one pass. That power suits demanding cut lists and larger signs.

It can also engrave many colors on stainless steel.

Dual fans, a built in airway and a temperature display help it run hard. The buzzer alarms above 55C.

A red crosshair helps position repeat cuts, and a focus bar sets focus fast.

In daily use the built in air assist improves clean edges and reduces burn marks. Better airflow helps the beam reach deeper into thick material.

Ventilation still needs to handle the extra smoke from fast cutting.

The trade off is size and need. At 4.53 lb and 5.68 inches long, it puts real load on a light D1 gantry.

It is also far more power than thin engraving needs.

Choose it for thick cutting, not for fine detail work. It suits users who cut thick material daily and can support its weight and cooling needs.

LASER TREE Laser ModuleCheck it on Amazon
7

Creality Falcon 2W 1064nm Infrared Laser Module: Best for Falcon metal work

Creality Falcon 2W 1064nm Infrared Laser Module, xTool D1 laser modules
9.2/10Our score
  • 1064nm infrared, 2W
  • 0.03mm spot, 600mm/s
  • Color engraving on stainless steel
  • Quick swap for Falcon A1 Pro

Infrared metal specialist for Falcon A1 Pro, not a D1 module.

See it on Amazon

Pros

  • Color engraving on metal
  • Very fine spot
  • Fast 600mm/s marking

Cons

  • Falcon A1 Pro only
  • Not for wood cutting

This suits Falcon A1 Pro owners who want metal. It is a 2W 1064nm infrared module with 0.03mm spot and 600mm/s speed, made to quick swap with a blue laser head.

Creality says it does color engraving on stainless steel. That color work sets it apart from simple dark marking.

It suits premium gifts and branded pieces where color matters.

In daily use it marks stainless steel, aluminum, titanium, brass, gold, silver, ABS and acrylic. The fine spot holds logos, QR codes and photos.

It is made for jewelry, gifts, tags and branding.

The quick swap design is a real plus for mixed material shops. You can switch between blue and infrared heads without a full machine change.

That saves time when orders move from wood to metal.

It is not a D1 module. It is listed only for the Falcon A1 Pro platform.

D1 owners should not buy it for fit or driver reasons.

If you own a Falcon, the swap system makes infrared easy to add. Test settings on scrap metal first, since finishes vary by alloy and coating.

Creality Falcon 2W 1064nm Infrared Laser ModuleCheck it on Amazon
8

ORTUR LU2-10A Laser Module for Laser Master: Best for Ortur frames

ORTUR LU2-10A Laser Module for Laser Master, xTool D1 laser modules
9.0/10Our score
  • 10W class, 24V
  • 0.05 x 0.1mm compressed spot
  • Cuts 20mm wood, 30mm acrylic
  • Dual fan, air assist interface

A refined 10W Ortur head with a very thin spot for portraits.

See it on Amazon

Pros

  • Thin spot for fine art
  • Strong thick cutting
  • Light body for speed

Cons

  • Ortur model list focus
  • 24V system needed

This suits Ortur owners who want fine detail with strong cutting. It gives 10W class power with a 0.05 x 0.1mm ultra thin spot, on a 24V system.

Ortur says it cuts 20mm wood and 30mm acrylic. That depth suits thicker projects without many repeat passes.

It still keeps a fine spot for detailed engraving work.

The thin square spot helps portraits and fine shading. Dual fans and a built in air assist interface support long runs.

The body is light at 235g, so motion stays fast.

In daily use it covers wood, metal, acrylic, stainless steel, glass, ceramics, leather, paper and fabric. That wide list suits custom gifts, coasters, key chains and business cards.

Test each material, since coatings change results.

Compatibility is the limit. It is listed for Ortur Laser Master 2, 2 Pro, 2 Pro S2 and Master 3.

A D1 owner must check mount, cable and 24V supply before any fit.

For Ortur frames, it is a strong upgrade. Set speed through LightBurn or LaserGRBL and keep cooling and exhaust in good order.

ORTUR LU2-10A Laser Module for Laser MasterCheck it on Amazon
9

LASER TREE 5W Laser Module: Best for 45mm fixed focus

LASER TREE 5W Laser Module, xTool D1 laser modules
8.1/10Our score
  • 5W class, 45mm fixed focus
  • Cuts 4mm plywood 80-100mm/min
  • Air assist, fan cooling
  • Adapter board included

A simpler 5W LASER TREE head with a longer 45mm focus for simpler setup.

See it on Amazon

Pros

  • Simple fixed focus
  • Adapter board included
  • Cleaner cuts with air assist

Cons

  • Slower cutting than 23mm models
  • Lower score for power

This suits buyers who want a simpler 5W head with a longer focus. It gives 5W class power at 45mm fixed focus, with air assist and fan cooling.

LASER TREE says it cuts 4mm plywood at 80 to 100mm/min. That speed suits thin plywood and general cutting jobs.

Air assist helps keep material edges cleaner and clearer.

The 45mm focus is easier to set and more forgiving on uneven stock. An adapter board helps match voltages and pins.

The kit includes a driver adapter, eye cover, spare glass, cable, wrench and focus plates.

In daily use it covers plywood, wood, stone, mirror stainless steel, black acrylic, plastic and leather. That range suits mixed hobby work.

The fan cooling helps during longer engraving runs.

The trade off is speed and spot size. The 23mm LASER TREE 5W above cuts faster and focuses tighter.

Choose this one if you value simple focus and included parts over maximum speed.

Check whether your machine needs a 12V or 24V version before ordering. The wrong voltage can stop the module from running safely.

LASER TREE 5W Laser ModuleCheck it on Amazon

How the xTool D1 laser module options stack up

Blue diode modules dominate this list because the D1 is a diode machine. Infrared modules rank high for metal, but they fit S1 and Falcon frames, not D1 frames.

That fit gap is why a 5W diode is the practical top pick for D1 owners.

ProductBest forWavelengthOutput powerSpot sizeOur score
xTool S1 1064nm Infrared Laser Modulemetal jewelry1064nm2W0.03mm9.7
LASER TREE Laser Engraving Moduleversatile 5W cutting450nm5W9.5
Quarton Economical Red Dot Laser Modulealignment and pointing650nmUnder 2.5mW9.4
LASER TREE 10W Laser Engraving Module10W cutting value450nm10W9.3
Genmitsu CFL55 Compressed Spot 5.5W FAC LaserGenmitsu owners5.5W0.1 x 0.1mm9.2
LASER TREE Laser Modulethick material cutting30W9.2
Creality Falcon 2W 1064nm Infrared Laser ModuleFalcon metal work1064nm2W0.03mm9.2
ORTUR LU2-10A Laser Module for Laser MasterOrtur frames10W class0.05 x 0.1mm9.0
LASER TREE 5W Laser Module45mm fixed focus5W class8.1

We compared wavelength, output power, spot size, focus length, input voltage, plug type, weight, included parts and listed materials. We checked which machines each head lists and which materials each head cannot engrave.

We did not test any head hands on.

Power numbers need care. Machine power, input power and optical output are different.

A 40W machine rating with 5W optical output is not a 40W laser. We used optical output where the data gives it.

Spot size and focus shape detail. A 0.03mm infrared spot holds jewelry detail.

A 0.05 x 0.1mm diode spot holds portraits. A 23mm focus cuts faster than a 45mm focus on the same power.

Fit, voltage and material limits together

Fit decides what you can mount, voltage decides what will run, and material limits decide what will mark. A head that wins on power can still fail on all three in daily use.

Check mount holes and cable type against the D1 head that came with your machine.

Is a blue diode or infrared module better for a D1?

A blue diode is better for a D1, because it fits the frame, driver and budget. Infrared is better for bare metal, but the S1 and Falcon infrared heads here do not fit a D1.

Blue diode for wood, acrylic and coated metal

Blue 450nm heads cut wood, plywood, MDF, cardboard, leather and dark acrylic. They also engrave coated or blackened metal, mirror stainless steel and metal with an oxide layer.

They cannot mark bare aluminum, gold or silver well.

Infrared for bare metal and jewelry

Infrared 1064nm marks bare metals dark and crisp. It also does color engraving on stainless steel.

That is why the xTool S1 1064nm infrared laser module review exists for S1 owners, not D1 owners.

The wavelength explains the split. Blue light is absorbed well by wood and dark plastics, which is why it cuts them in one pass.

Infrared light interacts differently with metals, which is why it can mark bare gold, silver and copper without paint or marking paper. Choosing the wrong wavelength for your main material wastes time on test cuts.

What voltage and plug does your D1 need?

Your D1 needs a module that matches its board voltage and plug. A 12V module on a 24V machine needs a driver adapter and external supply.

A 24V module needs a 24V board.

12V modules with adapters

The LASER TREE 5W at 23mm and the Genmitsu CFL55 need 12V. LASER TREE provides adapter plates for 2 pin and 4 pin cables.

You must supply the 12V power source for 24V machines.

24V modules for D1 Pro

The LASER TREE 10W, LASER TREE K30 and ORTUR LU2-10A need 24V. They draw more current and need better cooling.

Check that your board and supply can feed them at full power.

Adapters add points of failure, so keep wiring tidy and check polarity before first power on. The XH2.54 3 pin plug used by several heads carries PWM, ground and 12V or 24V, and a wrong pin order can stop modulation.

Match the plug diagram from the listing, not just the shape of the connector.

How much power do you actually need?

5W is enough for most D1 work, 10W is faster for thick cutting, and 30W is for production thick stock. More power also means more smoke, heat and ventilation needs.

5W for thin work and detail

5W cuts 4mm plywood in one pass and engraves fast on wood and acrylic. It is lighter and easier on a D1 gantry.

It is the best first upgrade for most owners.

10W and 30W for thick cutting

10W cuts 8mm to 20mm wood depending on model. 30W cuts 30mm pine in one pass.

Both need air assist, strong exhaust and careful focus. They suit sellers who cut thick signs and parts daily.

Power also changes how you plan jobs. A 5W head may need two passes on thicker stock, which doubles run time and smoke.

A 10W head can finish the same job in one pass, but it asks more from your gantry and your ventilation. Shorter focus heads use power more tightly, so spot and focus matter as much as the headline wattage.

Which materials will your module engrave?

Material limits matter more than power for many buyers. Blue diodes fail on light colors and bare metal.

Infrared handles bare metal but fails on wood cutting.

What blue diodes cannot engrave

LASER TREE heads cannot engrave blue, purple, white or transparent material. They also cannot engrave aluminum without an oxide layer.

Test on scrap before you run a paid order.

What infrared handles best

Infrared marks gold, silver, platinum, copper, aluminum, titanium and stainless steel. It also marks dark plastic, acrylic, leather and stone.

It will not cut thick wood or plywood.

Material lists in the data show the same pattern across brands. Blue heads list MDF, wood, paper, leather, bamboo, plastic and rubber, with coated metal as the metal option.

Infrared heads list metals first, then leather, opaque plastic, dark acrylic, stone, glass with marking paper and ceramic with marking paper. Read that order as a guide to what each head does best.

How do you set focus and keep a module clean?

Focus length sets speed and detail, and a clean lens keeps power where it should be. Set focus with the plates or bar that come with the head, then lock it before you cut.

Air assist blows smoke away from the lens and cuts cleaner edges. The 10W LASER TREE, Genmitsu CFL55, K30 and ORTUR LU2-10A all support air assist in some form.

Wipe the lens with a clean dry cloth and replace protective glass when it clouds.

Heat matters too. Dual fans on the K30 and ORTUR LU2-10A help long runs.

The K30 alarms at 55C. Let any hot head cool before you touch the mount or lens.

Cleaning and lens checks

Dust and oil on a lens scatter the beam and reduce cutting depth, even at full power. LASER TREE notes that lenses with oil or dust affect cutting ability, and the 10W kit includes spare protective window glass for that reason.

Check the window before each thick cut, and keep a clean cloth and spare glass in the kit.

What safety gear goes with a new module?

Eye protection rated for your wavelength is not optional. Blue heads need 450nm protection.

Infrared heads need 1064nm protection. A shield or enclosure helps, but it does not replace glasses.

Class 4 heads can burn skin and damage eyes from reflections. Work with a door closed, warn others in the room, and never disable interlocks.

Keep fire extinguisher and ventilation close, because wood and acrylic smoke is flammable and harsh.

If you use pens or other tools on your machine, read our guide on xtool m1 ultra pens how to use No, for D1 owners the key links are xtool s1 attachments for S1 owners planning add ons, and the xtool s1 1064nm infrared laser module review before you buy infrared for the wrong frame.

Verdict: which xTool D1 laser module should you buy?

Buy the LASER TREE 5W at 23mm if you want one balanced D1 upgrade. It cuts 4mm plywood in one pass, engraves mirror stainless steel, and fits most DIY frames with a 12V adapter.

Buy a 10W blue diode if thick cutting is your daily job. The LASER TREE 10W and ORTUR LU2-10A cut far thicker stock, but both need 24V and strong cooling.

Buy infrared only if you own the right frame. The xTool S1 and Creality Falcon infrared heads are excellent for metal and jewelry, but they are not D1 modules.

For D1 metal work, use a blue diode on coated metal or plan for a machine built for infrared.

The best xtool d1 laser module is the one that fits your board, your voltage and your materials. Match those three first, then choose power.

That order will save you return shipping and wasted test cuts.

Our top 3 picks at a glance

  1. 1 xTool S1 1064nm Infrared Laser Module
    Best for metal jewelry

    xTool S1 1064nm Infrared Laser Module

    9.7/10 our score

    See it on Amazon
  2. 2 LASER TREE Laser Engraving Module
    Best for versatile 5W cutting

    LASER TREE Laser Engraving Module

    9.5/10 our score

    See it on Amazon
  3. 3 Quarton Economical Red Dot Laser Module
    Best for alignment and pointing

    Quarton Economical Red Dot Laser Module

    9.4/10 our score

    See it on Amazon

Frequently asked questions

What is a laser module?

A laser module is the light source head that mounts on an engraver frame. It holds the diode or infrared source, lens, fan and driver.

Swapping modules changes power, wavelength, spot size and the materials you can engrave or cut.

Can the xTool S1 infrared module fit a D1?

No. xTool lists the S1 1064nm module as S1 only. A D1 owner should look at blue diode modules with TTL/PWM control and a matching voltage, then check mount holes and cable type before ordering.

Is 10W better than 5W for a D1?

10W cuts thicker wood and acrylic in fewer passes and engraves faster. It also needs a 24V supply, draws more power and makes more heat and smoke.

5W is lighter, simpler and enough for most thin work.

Do I need safety glasses for these modules?

Yes. Blue 450nm and infrared 1064nm modules are Class 4 or similar high risk lasers.

Use glasses rated for the wavelength, an enclosure or shield, and never look at the beam or reflections.

Keep children and pets out of the room.